features ? rohs lead-solder-exempt compliant ? new 3.3 v and 5 v output models ? universal input 85-264 vac ? industry-standard footprint: 7.00" x 4.30" x 1.97" (177.8mm x 109.2mm x 50.0mm) ? input transient & esd compliance to en61000-4-2/-3/-4 ? greater than 134,000 hours mtbf ? remote sense and overvoltage protection on single output units and main output of multiple output units ? options include overtemperature protection, power fail signal, chassis, & cover single-output model selection model output adjustment convection cooled forced air line load ripple & noise initial setting voltage range output current output current regulation regulation %p-p (note 1) accuracy map110-1005 5v 4.95v to 5.50v 16a 22a 0.2% 1% 1% 5.09v to 5.11v map110-1012 12v/15v 11.25v to 15.75v 7.5/6a (note 2) 10/8a (note 2) 0.1% 0.5% 1% 11.97v to 12.02v map110-1024 24v/28v 22.8v to 29.2v 3.8/3.2a (note 2) 5.0/4.3a (note 2) 0.1% 0.5% 1% 23.95v to 24.05v notes: 1) maximum peak-to-peak noise expressed as a percentage of output voltage, 20 mhz bandwidth. 2) map110-1012 output currents are expressed as 12v/15v operation. map110-1024 output currents are expressed as 24v/28v operati on. multiple-output model selection ? 80w convection cooled, 110w forced-air cooled (200 lfm) model output adjustment convection cooled forced air line load ripple & noise initial setting voltage range current (note 1) current regulation regulation %p-p (note 2) accuracy +5v 4.75v to 5.25v 12a/20a pk 12a/20a pk 0.2% 0.5% 1% 5.09v to 5.11v map110-4000 +12v fixed 5a/9a pk 5a/9a pk 0.2% 1% 1% 11.97v to 12.03v -12v fixed 1a/1.5a pk 1a/1.5a pk 0.2% 1% 1% -11.4v to -12.6v -5v fixed 1a/1.5a pk 1a/1.5a pk 0.2% 1.5% 1% -4.75v to -5.25v +5v 4.75v to 5.25v 12a/20a pk 12a/20a pk 0.2% 0.5% 1% 5.09v to 5.11v map110-4001 +24v fixed 3a/4.5a pk 3a/4.5a pk 0.1% 1% 1% 23.94v to 24.06v -12v fixed 1a/1.5a pk 1a/1.5a pk 0.1% 1% 1% -11.4v to -12.6v +12v fixed 1a/1.5a pk 1a/1.5a pk 0.1% 1% 1% 11.4v to 12.6v +5v 4.75v to 5.25v 12a/20a pk 12a/20a pk 0.2% 0.5% 1% 5.09v to 5.11v map110-4002 +12v fixed 5a/9a pk 5a/9a pk 0.1% 1% 1% 11.97v to 12.03v -12v fixed 1a/1.5a pk 1a/1.5a pk 0.1% 1% 1% -11.4v to -12.6v +12v fixed 1a/1.5a pk 1a/1.5a pk 0.1% 1% 1% 11.4v to 12.6v +5v 4.75v to 5.25v 12a/20a pk 12a/20a pk 0.2% 0.5% 1% 5.09v to 5.11v map110-4003 +15v fixed 5a/7.3a pk 5a/7.3a pk 0.1% 1% 1% 14.96v to 15.04v -15v fixed 1a/1.5a pk 1a/1.5a pk 0.1% 1% 1% -14.3v to -15.7v -5v fixed 1a/1.5a pk 1a/1.5a pk 0.2% 1.5% 1% -4.75v to -5.25v +5v 4.75v to 5.25v 12a/20a pk 12a/20a pk 0.2% 0.5% 1% 5.09v to 5.11v map110-4004 +24v fixed 3a/4.5a pk 3a/4.5a pk 0.1% 1% 1% 23.94v to 24.06v -15v fixed 1a/1.5a pk 1a/1.5a pk 0.1% 1% 1% -14.3v to -15.7v +15v fixed 1a/1.5a pk 1a/1.5a pk 0.1% 1% 1% 14.3v to 15.7v map110 ac-dc series data sheet apr 04, 2006 revised to jul 13, 2006 page 1 of 5 www.power-one.com power-one?s map110 series of power supplies combines low cost and universal input in a board-only power solution to meet commercial and industrial requirements. full international safety, emi, and esd compliance ensure worldwide acceptance. all un its bear the ce mark. wide dynamic output current and fixed-frequency operation simplifies system level operation. the map110 series is configured to an international standard footprint. input and output connections are made via popular single-row molex connectors. single output models feature wide-range output adjustability to meet a wide variety of standard and user-specific output voltag e requirements. description
multiple-output model selection (cont.) ? 80w convection cooled, 110w forced-air cooled (200 lfm) model output adjustment convection cooled forced air line load ripple & noise initial setting voltage range current (note 1) current regulation regulation %p-p (note 2) accuracy +5v 4.75v to 5.25v 12a/20a pk 12a/20a pk 0.2% 0.5% 1% 5.09v to 5.11v map110-4010 +12v fixed 5a/9a pk 5a/9a pk 0.1% 2% 1% 11.97v to 12.03v -5v fixed 1a/1.5a pk 1a/1.5a pk 0.2% 1.5% 1% -4.75v to -5.25v -12v fixed 3a/4a pk 3a/4a pk 0.3% 8% 1% -11.5v to -12.5v +5v 4.75v to 5.25v 12a/20a pk 12a/20a pk 0.2% 0.5% 1% 5.09v to 5.11v map110-4011 +12v fixed 5a/9a pk 5a/9a pk 0.1% 1% 1% 11.97v to 12.03v -12v fixed 1a/1.5a pk 1a/1.5a pk 0.1% 1% 1% -11.4v to -12.6v +24v fixed 1a/1.5a pk 1a/1.5a pk 0.1% 1% 1% 23.2v to 24.8v +5v 4.75v to 5.25v 12a/20a pk 12a/20a pk 0.2% 0.5% 1% 5.09v to 5.11v map110-4015 +12v fixed 5a/9a pk 5a/9a pk 0.1% 1% 1% 11.97v to 12.03v -15v fixed 1a/1.5a pk 1a/1.5a pk 0.1% 1% 1% -14.4v to -15.6v +15v fixed 1a/1.5a pk 1a/1.5a pk 0.1% 1% 1% 14.4v to 15.6v +12v 11.55v to 12.45v 5a/9a pk 5a/9a pk 0.2% 0.5% 0.5% 11.96v to 12.03v map110-4200 +24v fixed 4a/4.5a pk 4a/4.5a pk 0.2% 1% 1% 23.94v to 24.06v -12v fixed 1a/1.5a pk 1a/1.5a pk 0.2% 1% 1% -11.4v to -12.6v +5v fixed 2a/2.5a pk 2a/2.5a pk 0.2% 1.5% 1% 4.75v to 5.25v +3.3v 3.2v to 3.4v 12a/20a pk 15a/20a pk 0.3% 0.7% 1% 3.29v to 3.31v map110-4300 +5v fixed 5a/12a pk 8a/12a pk 0.2% 1% 1% 4.98v to 5.02v (note 3) -12v fixed 1a/1.5a pk 1a/1.5a pk 0.1% 1% 1% -11.4v to -12.6v +12v fixed 1a/1.5a pk 1a/1.5a pk 0.1% 1% 1% 11.4v to 12.6v +3.3v 3.2v to 3.4v 12a/15a pk 15a/20a pk 0.3% 0.7% 1% 3.29v to 3.31v map110-4305 +5v fixed 5a/12a pk 8a/12a pk 0.2% 1% 1% 4.98v to 5.02v (note 3) -5v fixed 1a/1.5a pk 1a/1.5a pk 0.1% 1% 1% -4.75v to -5.25v +12v fixed 1a/1.5a pk 1a/1.5a pk 0.1% 1% 1% 11.4v to 12.6v notes: 1) peak loads up to 110 watts for 60 seconds or less are acceptable, (10% duty cycle max.). peak power must not exceed 110 watt s. 2) maximum peak-to-peak noise expressed as a percentage of output voltage, 20 mhz bandwidth. 3) sum of the output currents of v1 + v2 may not exceed 15 a continuous, 22 a peak. maximum output rtating: model/output multiple output single output multiple output single output multiple output single output option board only board only ?l?-bracket ?l?-bracket ?c?-cover c?-cover convection continuous/peak 80w/110w 90w/120w 80w/110w 90w/120w 60w/110w 65w/120w forced air 200 lfm 110w 120w 110w 120w 110w 120w input specifications parameter conditions/description min nom max units input voltage - ac continuous input range. 85 264 vac input frequency ac input. 47 63 hz brown out protection lowest ac input voltage that regulation is maintained with full rated loads. 85 vac hold-up time nominal ac input voltage (110 vac) 50% load: 40 ms full rated load: 20 input current 85 vac (110w load). 3.5 a rms 110vac (110w load). 2.8 input protection non-user serviceable internally located ac input line fuse. inrush surge current internally limited by thermistor. vin = 264 vac (one cycle). 25 c. 41 a pk operating frequency switching frequency of main transformer, (fixed frequency). 20 25 khz map110 ac-dc series data sheet apr 04, 2006 revised to jul 13, 2006 page 2 of 5 www.power-one.com model numbers highlighted in yellow or shaded are not recommended for new designs.
output specifications parameter conditions/description min nom max units efficiency full load, 230 vac. varies with distribution of loads among outputs. 65 75 80 % minimum loads single output models. 0 amps multiple output models, v1 + v2 (note 1). 1 amps ripple and noise full load, 20 mhz bandwidth. see model selection chart. output power multiple output units with convection cooling. 5 80 watts multiple output units with 200 lfm forced air cooling. 5 110 watts overshoot / undershoot output voltage overshoot/undershoot at turn-on. 0 v regulation varies by output, regulation includes: line changes from 90-132 vac or 175-264, changes in load starting at 20% load and changing see model selection chart. to 100% load. transient response recovery time, to within 1% of initial set point due to a 50-100% load change, 4% max. deviation. (main output only on multiple output units). 500 s turn-on delay time required for initial output voltage stabilization. 1 sec turn-on rise time time required for output voltage to rise from 10% to 90%. 20 ms interface signals and internal protection parameter conditions/description min nom max units overvoltage protection provided on single output models and the map110-1005 6.10 7.20 main output of multiple output models. map110-1012 17.3 20.2 map110-1024 32.2 37.8 v map110-4200 13.8 16.2 map110-4300 3.7 4.35 all other models. 5.75 6.75 overload protection fully protected against output overload and short circuit. 150 200 % automatic recovery upon removal of overload condition. remote sense voltage drop compensated for at the load. 250 mv input power fail option, ttl compatible logic signal. time before regulation dropout due warning to loss of input power at 110 vac. active low. 3 5 ms overtemperature protection option, system shutdown due to excessive internal temperature. safety, regulatory, and emi specifications parameter conditions/description min nom max units agency approvals ul1950. csa 22.2 no. 234/950. approved. en60950 (tuv). dielectric withstand voltage input to output. 2600 vdc electromagnetic fcc cfr title 47 part 15 sub-part b - conducted & radiated. b interference, en55022 / cispr 22 conducted. b class conducted en55022 / cispr 22 radiated (note 2). a input transient protection en61000-4-5 level 3. 2 kv insulation resistance input to output. 10 m leakage current per en60950, 264 vac. 750 a notes: 1) minimum load is required only to meet the regulation limits of v3 and v4. if v3 and v4 are unused, no minimum load is neces sary. 2) the following units meet class b: map110-1005, map110-4000/4011/4015/4200/4300. map110 ac-dc series data sheet apr 04, 2006 revised to jul 13, 2006 page 3 of 5 www.power-one.com
environmental specifications parameter conditions/description min nom max units altitude operating. 10k asl ft. non-operating. 50k asl ft. operating temperature derate linearly above 50c by 2.5% per c at 100% load: 0 50 c to a maximum temperature of 70c. at 50% load: 0 70 c storage temperature -55 85 c temperature coefficient 0c to 70c. 0.03 0.05 %/c relative humidity non-condensing. 95 %rh options description notes dimensions l-bracket add ?l? suffix to model number. 7.15" x 4.50" x 2.40" (182.0mm x 115.0mm x 61.0mm) cover add ?c? suffix to model number. includes l-bracket. 7.20" x 4.50" x 2.40" (183.0mm x 115.0mm x 61.0mm) power fail add ?p? suffix to model number. provides >5 ms typical warning time before n/a signal main output drops 5%. warning time increases at reduced load levels. thermal add ?t? suffix to model number. initiates shut-down in the event of an overtemperature n/a shutdown condition. automatic recovery. map110 ac-dc series data sheet apr 04, 2006 revised to jul 13, 2006 page 4 of 5 www.power-one.com
note 1 overall size: 7.00" x 4.30" x 1.97" (177.8mm x 109.2mm x 50.0mm) overall weight: 1.3 lb (0.59 kg) contact factory for dimensions for l-bracket and cover. map110 ac-dc series data sheet apr 04, 2006 revised to jul 13, 2006 page 5 of 5 www.power-one.com nuclear and medical applications - power-one products are not designed, intended for use in, or authorized for use as critical c omponents in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written conse nt of the respective divisional president of power-one, inc. technical revisions - the appearance of products, including safety agency certifications pictured on labels, may change dependin g on the date manufactured. specifications are subject to change without notice.
|
